ʱʱapp

Related Magazines Related Associations Related Books
hot key words: Drying equipment flash dryer spray dryer sludge dryer fluidized fluid bed belt dryer paddle dryer disc dryer vibrating screen centrifugal pump disperser
Your present location: Home >> Technology Channel >> Industry Knowledge >> Correct maintenance and maintenance is an important guarantee to improve the service life of acid and alkali resistant fans

Correct maintenance is an important guarantee to improve the service life of acid and alkali resistant fans

Release time: 2019/10/25 Clicks: 1903

Correct maintenance and maintenance is an important guarantee for the safe and reliable operation of the fan and an increase in the service life of the acid and alkali resistant fan. Therefore, when using the acid and alkali resistant fan, the maintenance and maintenance of the acid and alkali resistant fan must be paid full attention.

Impeller maintenance:

At the beginning of the impeller operation and all regular inspections, whenever possible, the impeller must be inspected for defects such as cracks, wear, and dust accumulation.

Whenever possible, the impeller must be kept in a clean state, and the dust and rust on it must be periodically removed with a wire brush, because with the increase of the operating time, it is impossible for these dusts to adhere to the impeller uniformly, resulting in Impeller balance is broken, causing rotor vibration.

Once the impeller has been repaired, it needs to be rebalanced. If possible, you can use a portable trial balancer to perform on-site balancing. Before performing balancing, all tightening bolts must be checked for tightening. Because the impeller has been running unbalanced for some time, these bolts may have become loose.

Bearing maintenance:

Always check the bearing lubricant supply. If there is oil leakage in the box, you can tighten the bolts of the end caps. If this is not possible, you may have to replace with new sealing packing.

The bearing lubricant should be replaced at least once in half a year during normal use. For the first use, it should be performed after about 200 hours of operation. The second oil change should be performed within 1 to 2 months. After that, the lubricant should be checked once a week. If the lubricating oil has not deteriorated, the oil change can be extended to once every 2 to 4 months. When replacing, you must use the specified grade of lubricating oil, and thoroughly drain and clean the old oil in the tank before filling with new oil.

If you need to replace the fan bearing seat, you should pay attention to the following:

Before installing a new bearing, the bearing and the bearing box must be cleaned. The bearing is placed in oil with a temperature of about 70-80 C and heated before being loaded on the shaft. It must not be forcibly assembled to avoid injury to the shaft.

Case maintenance:

Except for regular inspection of the casing and the interior of the intake chamber for serious wear and tear and removal of serious dust deposits, these areas may not be subject to other special maintenance. Regularly check whether all the fastening bolts are tight. For the fan with the compression bolts, press the butterfly spring on the feet to the installation height specified in the drawing.

[Source: Suzhou Dingyu Energy Saving Equipment Co., Ltd.] [ Favorite this page ] [ Print this page ] [ Close ]
  • ① All works marked "Source: Chemical Machinery Network" on this website, the copyright belongs to Chemical Machinery Network, please reprint the website of Chemical Machinery (http://z-han.com). Violators of this website will be held responsible for relevant legal responsibilities.
  • ② All works on this website that do not indicate "Source: Chemical Machinery Network" are reproduced from other carriers. The purpose of reprinting is to convey more information, and does not mean that this website agrees with its views or confirms the authenticity of its content. When other media, websites or individuals use this work from this website, they shall bear their own legal responsibilities such as copyright.
  • ③ All information published on this website does not declare or guarantee the correctness or reliability of its content; you hereby accept and acknowledge that the risks arising from relying on any information shall be borne by yourself.
  • ④ If you are involved in the content of the work, copyright or other issues, please contact this website within one week from the date of publication of the work, otherwise it is deemed to waive the relevant rights.
About Us - Contact Us - Announcement - Terms of Service - Site Help - Business Services - Legal Statement - Legal Counsel - Friend Links - Online Consulting - Site Map
National Customer Service Hotline: 400-667-8871
Copyright ? 2004-2013 Chemical Machinery Network z-han.com Jiangsu Dongwang Information Technology Co., Ltd. All rights reserved
  • Advertising business (image advertising, membership application): 400-667-8871
  • Equipment procurement (equipment procurement, shopping guide consultation): 400-667-8871
  • Information editor (member review, information release): 400-667-8871
  • Media cooperation (exhibitions, associations, magazines): 400-667-8871
  • Human resources: 400-667-8871
  • Fax: 0519-89897519
Su ICP prepares 05005804 value-added telecommunications business license Su B2-20110228 E-mail: